Effects of Side Flattening on Torsional and Cyclic Fracture Resistance of Nickel-Titanium File.

INTRODUCTION: The purpose of this study was to evaluate the effect of side flattening of cutting flutes on the cyclic resistance and torsional resistance of nickel-titanium files. METHODS: Both novel flattened Platinum V.EU (PL) and standard non-flattened CC Premium V.EU (CC) rotaries were tested. For cyclic fatigue tests, all the files were rotated in an artificial root canal with a curvature of 45° and a radius of 6.06 mm at 300 rpm (n = 15 in each group). The number of cycles to failure (NCF) was calculated. For torsional tests, the files were rotated at 2 rpm clockwise until fracture occurred. The maximum torque value at fracture was measured and the toughness and distortion angle were computed. Subsequently, five fragments were randomly selected in each experiment, the cross-section and longitudinal direction of the fragments were photographed using a scanning electron microscope. An unpaired t-test was performed at a significance level of 95%. RESULTS: There was a statistically significant difference in NCF between CC and PL (P < .05). CC showed higher NCF than PL. There was no statistically significant difference between CC and PL with regards to the parameters related to torsional resistance (distortion angle, ultimate strength, and toughness) (P > .05). CONCLUSION: Within the limitations of this study, side flattening of the file did not improve cyclic resistance or torsional resistance of the files. As side flattening may reduce a file's cyclic resistance, such files should be used with caution in clinical practice.

The application of lasers in vital pulp therapy: clinical and radiographic outcomes.

The main purpose of vital pulp therapy (VPT) is to preserve the integrity and function of the pulp. A wide variety of materials and techniques have been proposed to improve treatment outcomes, and among them, the utilization of lasers has gained significant attention. The application of lasers in different stages of VPT has witnessed remarkable growth in recent years, surpassing previous approaches.This study aimed to review the applications of lasers in different steps of VPT and evaluate associated clinical and radiographic outcomes. An electronic search using Scopus, MEDLINE, Web of Science and Google Scholar databases from 2000 to 2023 was carried out by two independent researchers. The focus was on human studies that examined the clinical and/or radiographic effects of different laser types in VPT. A total of 4243 studies were included in this narrative review article. Based on the compiled data, it can be concluded that although current literature suggests laser may be proposed as an adjunct modality for some procedural steps in VPT, more research with standardized methodologies and criteria is needed to obtain more reliable and conclusive results.

Effect of strontium fluoride on mechanical and remineralization properties of enamel: An in-vitro study on a modified orthodontic adhesive.

OBJECTIVES: Evaluate the ability of strontium fluoride on bond strength and enamel integrity after incorporation within orthodontic adhesive system as a delivery vehicle. METHODS: Experimental orthodontic adhesive system Transbond™ XT were modified with 1% Sr2+, 0.5% SrF2, 1% strontium, 0.5% Sr2+, 1% F-, 0.5% F-, and no additions were control. Mixing of formulation was monitored using Fourier transform infrared spectroscopy. Small-molecule drug-discovery suite was used to gain insights into Sr2+, F-, and SrF2 binding. Shear bond testing was performed after 6-months of ageing. Enamel blocks were cut, and STEM pictures were recorded. Specimens were indented to evaluate elastic modulus. Raman microscope was used to collect Raman spectra and inspected using a scanning electron microscope. Crystal structural analysis was performed using X-ray diffraction. Effect of material on cellular proliferation was determined. Confocal was performed to evaluate the effect of formulation on biofilms. RESULTS: FTIR of modified adhesives depicted peak changes within range due to various functional groups existing within samples. TEM represented structurally optimized hexagonal unit-cell of hydroxyapatite. Mean shear bond strength is recorded highest for Transbond XT with 1% SrF2. Dead bacterial percentage appeared higher in 0.5% SrF2 and 1% F- specimens. Crystal lengths showed an increase in 0.5% and 1% SrF2 specimens. Phase contrast within TEM images showed a union of 0.5% SrF2 crystal with enamel crystal with higher elastic modulus and highly mineralized crystalline hydroxyapatite. Intensity of ν1 PO43- and ν1 CO32- along with carbonate - / ν1PO43- ratio displayed good association with strontium fluoride. The formulation showed acceptable cell biocompatibility (p < 0.353). All specimens displayed characteristic diffraction maxima of different apatite angles within XRD. SIGNIFICANCE: Experimental results suggested good biocompatibility, adequate mechanical strength, and far-ranging crystallization ability. This would provide a new strategy to overcome the two major challenges of fixed orthodontics, biofilm growth, and demineralization of enamel.

Vital pulp therapy-Factors influencing decision-making for permanent mature teeth with irreversible pulpitis: A systematic review.

BACKGROUND: There is an increased tendency towards adopting minimally invasive interventions in dentistry, supported by advancement in materials and techniques. However, the decision-making process in choosing conservative or invasive treatments is influenced by several factors, particularly in permanent teeth with irreversible pulpitis. OBJECTIVES: The objective of the study was to systematically review the literature regarding factors that influence decision-making for vital pulp therapy (VPT) as definitive treatment option in permanent mature teeth diagnosed with irreversible pulpitis. METHODS: Two independent reviewers searched five electronic databases (PubMed, Embase, Web of Science, Scopus and Cochrane Library). Grey literature was searched through Google Scholar and contact with experts. Defined search keys were applied, and all peer-reviewed literature published with no language nor publication date limits were included. The All studies investigating the factors influencing treatment decision-making in mature permanent teeth with irreversible pulpitis were included. The quality of included studies was assessed by two independent reviewers using the Joanna Briggs Institute quality assessment tool. RESULTS: Six articles were included in the review. All included studies used questionnaires to characterize clinician preferences and attitudes in choosing treatment options for mature permanent teeth with irreversible pulpitis. The available evidence suggests that dentist-related factors have a significant influence on the chosen treatment in teeth with irreversible pulpitis, with speciality training and years of experience influencing the choice of VPT over other treatment options. COVID-19 reportedly swayed the dentists' decision to favour VPT. Only one article studied the influence of patient-related factors, such as age and presence of spontaneous pain on decision-making. Of note, a history of cardiovascular disease moved dentists towards prescribing VPT. DISCUSSION: Collectively, the included studies demonstrated an overriding influence of dentist-related factors on choosing among treatment options for painful teeth diagnosed with irreversible pulpitis. Patient-related factors were acknowledged but there are also potential factors such as socio-economic constraints that were not included in the component studies. CONCLUSION: In teeth with irreversible pulpitis clinicians educational background influence the decision towards a specific treatment option. Further data, preferably derived from clinical records, is necessary in future investigations to explore the effect of other important factors related to both dentists and patients. REGISTRATION: PROSPERO database (CRD42022339653).

The dental microscope in endodontic education: A feasibility study of a distance learning course.

This study aimed to evaluate the feasibility of preclinical training, specifically in root canal preparation, using a virtual educational system equipped with an operating microscope. Ten postgraduate general dentistry trainees and practitioners undergoing postgraduate training in endodontics participated. The telesimulation course included three steps: theory, demonstration of practical work by the teacher and lastly practical training by the participants. The digital environment including the dental microscope was presented, and the feedback was collected with a questionnaire. The majority of participants considered that the online video conference format allowed them to acquire theoretical content but also practical knowledge and skills, owing to the contribution of the operating microscope. The technical feasibility of endodontic telesimulation was demonstrated. The operating microscope has a potential role in distance education, enabling teaching to occur synchronously and collaboratively. This allows learners to interact with each other and demonstrators in real time.

Morphology of pulpal mineralizations: A scoping review.

OBJECTIVE: The aim of this scoping review was to summarize and discuss the morphological features and associated factors of pulpal mineralizations (PMs) as described within the literature. DATA: The study protocol was registered on the Open Science Framework platform and is available at the following link: https://osf.io/hfqwe. This scoping review was developed according to the PRISMA-ScR guidelines. SOURCES: A literature search of four electronic databases was performed in SCOPUS, MEDLINE (PubMed), EMBASE and Word of Science, with the last search on May 29, 2023. Study selection was completed by two reviewers independently. Data was extracted regarding study characteristics, types, and features of PM and associated factors. STUDY SELECTION: Of 1016 studies initially identified ten which qualified were included in this scoping review. Systemic and local factors that result in pulpal insult can contribute to the development of PMs. Three forms of PM have been reported, pulp stones, diffuse mineralizations, and mineralized ectopic connective tissue, with discrete and diffuse mineralization being the two clinically relevant forms. The different forms of PMs exhibit dissimilar morphological features. CONCLUSION: Pulpal mineralizations exist in two clinically relevant forms: diffuse and discrete mineralizations and are likely associated with a pulpal insult. CLINICAL SIGNIFICANCE: Understanding the morphology of dental pulp mineralization is the first step to expanding the knowledge of pulp mineralization and could result in improved diagnosis of endodontic pathosis.

Treatment of pulpal and apical disease: The European Society of Endodontology (ESE) S3-level clinical practice guideline.

BACKGROUND: The ESE previously published quality guidelines for endodontic treatment in 2006; however, there have been significant changes since not only in clinical endodontics but also in consensus and guideline development processes. In the development of the inaugural S3-level clinical practice guidelines (CPG), a comprehensive systematic and methodologically robust guideline consultation process was followed in order to produce evidence-based recommendations for the management of patients presenting with pulpal and apical disease. AIM: To develop an S3-level CPG for the treatment of pulpal and apical disease, focusing on diagnosis and the implementation of the treatment approaches required to manage patients presenting with pulpitis and apical periodontitis (AP) with the ultimate goal of preventing tooth loss. METHODS: This S3-level CPG was developed by the ESE, with the assistance of independent methodological guidance provided by the Association of Scientific Medical Societies in Germany and utilizing the GRADE process. A robust, rigorous and transparent process included the analysis of relevant comparative research in 14 specifically commissioned systematic reviews, prior to evaluation of the quality and strength of evidence, the formulation of specific evidence and expert-based recommendations in a structured consensus process with leading endodontic experts and a broad base of external stakeholders. RESULTS: The S3-level CPG for the treatment of pulpal and apical disease describes in a series of clinical recommendations the effectiveness of diagnosing pulpitis and AP, prior to investigating the effectiveness of endodontic treatments in managing those diseases. Therapeutic strategies include the effectiveness of deep caries management in cases with, and without, spontaneous pain and pulp exposure, vital versus nonvital teeth, the effectiveness of root canal instrumentation, irrigation, dressing, root canal filling materials and adjunct intracanal procedures in the management of AP. Prior to treatment planning, the critical importance of history and case evaluation, aseptic techniques, appropriate training and re-evaluations during and after treatment is stressed. CONCLUSION: The first S3-level CPG in endodontics informs clinical practice, health systems, policymakers, other stakeholders and patients on the available and most effective treatments to manage patients with pulpitis and AP in order to preserve teeth over a patient's lifetime, according to the best comparative evidence currently available.

The application of lasers in vital pulp therapy: a review of histological effects.

Vital pulp therapy (VPT) is primarily intended to preserve the vitality of pulp tissues, which have been exposed for any reason. Various materials and techniques have been proposed to improve treatment outcomes, including the use of lasers. This study aimed to review the histological results of different dental lasers including low-level lasers, carbon dioxide (CO2), erbium-doped yttrium aluminum garnet laser (Er:YAG), neodymium-doped yttrium aluminum garnet (Nd:YAG), erbium, chromium:yttrium-scandium-gallium-garnet (Er,Cr:YSGG) lasers, and diode lasers for VPT. This focused review included a comprehensive electronic search of Scopus, MEDLINE, Web of Science, and Google Scholar databases from 2000 to 2022 by two independent investigators. Different combinations of keywords were used, and reference mining of related papers was done. The review included studies related to histologic evaluation of laser-assisted vital pulp therapy that stated the laser parameters that were used. Articles with radiographic or clinical assessments or articles lacking necessary data were excluded. Non-English articles were excluded unless their abstract was in English and encompassed the necessary data. Most studies indicated the efficacy of lasers for reduction of inflammation, acceleration of healing, and increasing the thickness of dentinal bridge. According to the evidence, lasers used in combination with pulp capping agents are beneficial to enhance the success rate of VPT.

Applying artificial intelligence to detect and analyse oral and maxillofacial bone loss-A scoping review.

Radiographic evaluation of bone changes is one of the main tools in the diagnosis of many oral and maxillofacial diseases. However, this approach to assessment has limitations in accuracy, inconsistency and comparatively low diagnostic efficiency. Recently, artificial intelligence (AI)-based algorithms like deep learning networks have been introduced as a solution to overcome these challenges. Based on recent studies, AI can improve the detection accuracy of an expert clinician for periapical pathology, periodontal diseases and their prognostication, as well as peri-implant bone loss. Also, AI has been successfully used to detect and diagnose oral and maxillofacial lesions with a high predictive value. This study aims to review the current evidence on artificial intelligence applications in the detection and analysis of bone loss in the oral and maxillofacial regions.

Evaluating the stress of root canal treatment in patients and dentists compared to other dental treatments: A systematic review and meta-analysis.

This systematic review aimed to investigate whether root canal treatment caused greater stress than other dental treatments for patients and dentists. All peer-reviewed literature published in English between January 1990 and January 2023 was included. This included randomized/non-randomized control trials, cohort studies, case-control studies, and cross-sectional studies. An electronic search used PubMed, Scopus, Medline, Cochrane Collaboration, and Embase. Hand searching supplemented the screening pool. Studies examining physiological or psychological stress measures within patients or providers of dental treatment (dentists, dental specialists, and dental students) were eligible. The study must have reported on the stress outcome for root canal treatment and at least one other dental procedure. After screening 3639 eligible records, there were 23 studies included, varying from very-low to low certainty of evidence. This review found that root canal treatment was more psychologically stressful for patients than routine restorative or cleaning procedures. However, the stress of root canal treatment relative to other dental procedures, especially extractions, was inconclusive for both dental patients and providers. Since patients regard root canal treatment as more stress-evoking than other routine dental procedures, providers should endeavour to minimise their own bias toward root canal treatment when providing adequate information for an informed treatment choice.

Pulpal anesthesia of maxillary first molars using 4% articaine infiltration in patients with symptomatic irreversible pulpitis: a randomized controlled clinical trial.

OBJECTIVES: This study aimed to compare the anesthetic efficacy of 1.8 mL (one cartridge) and 3.6 mL (two cartridges) buccal infiltration and buccal plus palatal infiltration of 4% articaine in maxillary first molar teeth with symptomatic irreversible pulpitis. MATERIALS AND METHODS: This randomized single-blind clinical trial was conducted on 45 patients with symptomatic irreversible pulpitis of maxillary first molars (Trial Registration No: IRCT2015011020238N2_2015). The patients were randomly divided into three groups (n = 15) for buccal infiltration of 1.8 mL articaine plus 1:100,000 epinephrine (group 1), buccal infiltration of 3.6 mL articaine (group 2), and buccal infiltration of 1.8 mL articaine plus palatal infiltration of 0.5 mL articaine (group 3). The pain intensity was measured by the Heft-Parker visual analog scale (VAS) during injection and during access cavity preparation. No pain or mild pain during treatment was considered as successful anesthesia. Data were analyzed by the Tukey's post hoc test. RESULTS: The three groups had a significant difference in frequency of the perceived pain during injection (P = 0.01). A higher volume of 4% articaine and injection of articaine in both buccal and palatal sides provided a significantly higher anesthesia success rate (P = 0.049 and P < 0.01, respectively). The highest success rate was recorded in group 3 (93.33%) followed by group 2 (80%) and then group 1 (53.33%). CONCLUSIONS: Increasing the administered volume of 4% articaine with 1:100,000 epinephrine and addition of palatal infiltration to buccal infiltration of articaine can significantly increase the success of anesthesia in maxillary first molars with symptomatic irreversible pulpitis. CLINICAL RELEVANCE: Achieving deep anesthesia in teeth with irreversible pulpitis is a critical parameter in management of patients who are in urgent need of root canal treatments.

The Influence of Cone Beam Computed Tomography-Derived 3D-Printed Models on Endodontic Microsurgical Treatment Planning and Confidence of the Operator.

INTRODUCTION: Currently, there are no studies evaluating the impact of 3-dimensional (3D) printed models on endodontic surgical treatment planning. The aims of this study were: 1) to determine if 3D models could influence treatment planning; and 2) to assess the effect of 3D supported planning on operator confidence. MATERIALS: Endodontic practitioners (n = 25) were asked to analyze a preselected cone beam computed tomography (CBCT) scan of an endodontic surgical case and answer a questionnaire that elucidated their surgical approach. After 30 days, the same participants were asked to analyze the same CBCT scan. Additionally, participants were asked to study and to perform a mock osteotomy on a 3D printed model. The participants responded to the same questionnaire along with a new set of questions. Responses were statistically analyzed using chi square test followed by either logistic or ordered regression analysis. Adjustment for multiple comparison analysis was done using a Bonferroni correction. Statistical significance was set at ≤0.005. RESULTS: The availability of both the 3D printed model and the CBCT scan resulted in statistically significant differences in the participants' responses to their ability to detect bone landmarks, predict the location of osteotomy, and to determine the following: size of osteotomy, angle of instrumentation, involvement of critical structures in flap reflection and involvement of vital structures during curettage. In addition, the participants' confidence in performing surgery was found to be significantly higher. CONCLUSIONS: The availability of 3D printed models did not alter the participants' surgical approach but it significantly improved their confidence for endodontic microsurgery.

Immunomodulatory Effects of Endodontic Sealers: A Systematic Review.

Inflammation is a crucial step prior to healing, and the regulatory effects of endodontic materials on the immune response can influence tissue repair. This review aimed to answer whether endodontic sealers can modulate the immune cells and inflammation. An electronic search in Scopus, Web of Science, PubMed, and Google Scholar databases were performed. This systematic review was mainly based on PRISMA guidelines, and the risk of bias was evaluated by SYRCLEs and the Modified CONSORT checklist for in vivo and in vitro studies, respectively. In total, 28 articles: 22 in vitro studies, and six in vivo studies were included in this systematic review. AH Plus and AH 26 can down-regulate iNOS mRNA, while S-PRG sealers can down-regulate p65 of NF-κB pathways to inhibit the production of TNF-α, IL-1, and IL-6. In vitro and in vivo studies suggested that various endodontic sealers exhibited immunomodulatory impact in macrophages polarization and inflammatory cytokine production, which could promote healing, tissue repair, and inhibit inflammation. Since the paradigm change from immune inert biomaterials to bioactive materials, endodontic materials, particularly sealers, are required to have modulatory effects in clinical conditions. New generations of endodontic sealers could hamper detrimental inflammatory responses and maintain periodontal tissue, which represent a breakthrough in biocompatibility and functionality of endodontic biomaterials.

Design of an interactive system for access cavity assessment: A novel feedback tool for preclinical endodontics.

INTRODUCTION: A software program was developed to provide visual, guided feedback to students for access cavity preparations in preclinical learning. The specific aim of the study was to investigate students' overall experiences with the new learning method and compare their experiences with traditional teaching. MATERIALS AND METHODS: A workflow based on freely available software was designed to interactively register three-dimensional models of molars with access cavities, and to metrically compare these to instructor-prepared standard cavities. Third-year students practicing molar endodontics access cavity preparation in the preclinical course were then surveyed. A total of 44/79 students completed self-administered questionnaires prior and after the use of the feedback software to gauge their learning experience. RESULTS: The results of the post-training questionnaire illustrated that all surveyed students agreed/strongly agreed that the software assisted their learning in access cavity preparation. In addition, 86 and 89%, respectively, of students agreed that the use of the software improved their skills of access cavity preparation and felt more confident about their access cavity preparation skills after using the software package, 3D Dental Align. DISCUSSION: The presented software solution permitted setting and comparing access cavity preparations by students against a standard access prepared by an instructor. The process of data acquisition and registration was fast and straightforward. Student feedback was very positive and suggested the integration of this type of experiential learning into the preclinical curriculum. CONCLUSION: This feasibility study demonstrated the utility of the new technology to assist dental students' access cavity preparation learning.

Advancing Nitinol: From heat treatment to surface functionalization for nickel-titanium (NiTi) instruments in endodontics.

Nickel-titanium (NiTi) alloy has been extensively researched in endodontics, particularly in cleaning and shaping the root canal system. Research advances have primarily focused on the design, shape, and geometry of the NiTi files as well as metallurgy and mechanical properties. So far, extensive investigations have been made surrounding surface and thermomechanical treatments, however, limited work has been done in the realm of surface functionalization to augment its performance in endodontics. This review summarizes the unique characteristics, current use, and latest developments in thermomechanically treated NiTi endodontic files. It discusses recent improvements in nano-engineering and the possibility of customizing the NiTi file surface for added functionalization. Whilst clinical translation of this technology has yet to be fully realized, future research direction will lie in the use of nanotechnology.

Mechanical and Metallurgical Characterization of Nickel-Titanium Wire Types for Rotary Endodontic Instrument Manufacture.

This study aimed to evaluate and compare the effects of ambient temperature and post-manufacture heat-treatment on the mechanical behavior of nickel-titanium (NiTi) wires. Four types of commercial NiTi variants (Stock NiTi, heat treated "Blue", "Gold", "Superflex", all Dentsply Maillefer, Ballaigues, Switzerland) were stressed in a tensile testing machine in a temperature-controlled water bath at three different temperatures. Stress and strain values were extrapolated from the raw data, and 2-way ANOVA and Tukey's test for multiple comparisons were performed to compare the differences of the mechanical constants. Differential scanning calorimetry (DSC) tests established the martensitic transformation starting (Ms), finishing (Mf) and austenitic (reverse-martensitic) starting (As) and finishing (Af) points. Austenitic modulus of elasticity and transformation stress values increased with temperature for all NiTi groups. The martensitic modulus of elasticity, maximum transformation strain and ultimate tensile stress were not significantly affected by temperature changes. Stock NiTi and Gold wire samples presented with clearly delineated austenitic and martensitic transformations in the DSC experiments. Differences in manufacturing/heat treatment conditions and ambient temperature affect the mechanical behavior of nickel-titanium and may have clinical implications. Further improvements to the experimental setup could be considered to provide more accurate measurements of strain.

Physicochemical and biological properties of four calcium silicate-based endodontic cements.

Background/purpose: Several brands of calcium silicate-based cements (CSBCs) are currently marketed. Here we compared physicochemical and biological properties of new products Ortho MTA (BioMTA), Retro MTA (BioMTA), and EZ-Seal (Ezekiel) to widely used ProRoot MTA (Dentsply Tulsa). Materials and methods: CSBCs were analyzed by X-ray diffractometry and examined by scanning electron microscopy. Elemental composition was determined by energy dispersive spectroscopy. Particle size was measured by particle size analyzer. Human stem cells from apical papilla (SCAPs) were incubated with eluates from CSBCs. Survival of SCAP cells was evaluated with MTT assay. The Alizarin red S stain was used to identify calcified nodules formed in SCAP cultures. The effects of CSBC eluates on SCAP proliferation and migration were examined using an in-vitro scratch "wound-healing" assay. Results: All CSBC specimens showed similar X-ray diffraction patterns. The average particle size of EZ-Seal was smaller than ProRoot MTA, Ortho MTA, and Retro MTA (P < 0.001). The least cytotoxicity of eluates was found for EZ-Seal. In the Alizarin red S staining test, calcified nodules were observed in cultures with ProRoot MTA, Ortho MTA, and Retro MTA, however, no calcified nodules were observed in cultures with EZ-Seal. SCAP proliferation and migration capacity in presence of EZ-Seal was higher than with ProRoot MTA, Ortho MTA, and Retro MTA (P < 0.001). Conclusion: EZ-Seal has a smaller average particle size and a better cytocompatibility than all other examined CSBCs.

Diagnosis consensus among endodontic specialists and general practitioners: An international survey and a proposed modification to the current diagnostic terminology.

INTRODUCTION: This survey aimed to determine the consensus amongst endodontic specialists in North America and practitioners worldwide to diagnose the pulp and periapical conditions of selected case scenarios encountered in daily practice using the American Association of Endodontists (AAE) pulpal and periapical diagnostic terms. Secondly, an attempt was made to suggest modifications in terms accordingly. METHODOLOGY: A survey designed by two endodontic educators was sent to endodontists in North America and clinicians worldwide through an electronic database. The survey included socio-demographic questions followed by the clinical and radiographic presentations of four clinical scenarios. The participants were then requested to provide the pulpal and the periapical diagnosis of 11 teeth presented in these cases (22 answers in total/participant) using the AAE diagnostic terminology. Cases were designed to include 12 pulpal/periapical conditions as control (non-controversial conditions) and ten so-called controversial conditions. A proportion threshold of 10% was required for any diagnostic term to be reported in this survey. The participants were divided into two groups based on the region of endodontic training and/or practice to 'Specialised North American' or 'International Practitioners,' and their results were statistically compared using chi-squared tests (p < .05). RESULTS: The survey included 421 participants. 74% were endodontists, and 46.1% were amongst the 'Specialised North American' group and 53.9% amongst the 'International Practitioners'. Eleven of 12 control conditions had an almost complete agreement amongst the participants regarding the diagnostic terms selected, ranging between 82% and 96%, with no other diagnostic term exceeding the 10% threshold. All the controversial conditions yielded more than one diagnostic term selected/condition that exceeded the 10% threshold for groups ('Specialised North American' and 'International practitioners'). There were no differences in the diagnostic terms selected between the two groups; however, the weight for each term varied between the groups in some cases. CONCLUSION: There is a lack of consensus amongst clinicians, regardless of their training and region of practice, on the appropriate diagnostic terms to be used in particular clinical conditions. More diagnostic terms and modifications in the current terms may be required to establish a more reliable diagnostic terminology.